Differences

This shows you the differences between two versions of the page.

@@ Line 1: / Line 1: @@
+====== Installed CPAN on Ubuntu ======
+Command: perl -MCPAN -e shell
+Reply:
+<code>
+/etc/perl/CPAN/Config.pm initialized.
+CPAN is the world-wide archive of perl resources. It consists of about
+sites that all replicate the same contents all around the globe.
+Many countries have at least one CPAN site already. The resources
+found on CPAN are easily accessible with the CPAN.pm module. If you
+want to use CPAN.pm, you have to configure it properly.
+If you do not want to enter a dialog now, you can answer 'no' to this
+question and I'll try to autoconfigure. (Note: you can revisit this
+dialog anytime later by typing 'o conf init' at the cpan prompt.)
+Are you ready for manual configuration? [yes]
+CPAN build and cache directory? [/home/senthil/.cpan] /var/spool/cpan
+Cache size for build directory (in MB)? [10]
+Perform cache scanning (atstart or never)? [atstart]
+Cache metadata (yes/no)? [yes]
+Your terminal expects ISO-8859-1 (yes/no)? [yes]
+File to save your history? [/var/spool/cpan/histfile]
+Number of lines to save? [100]
+Policy on building prerequisites (follow, ask or ignore)? [ask] follow
+Where is your gzip program? [/bin/gzip]
+Where is your tar program? [/bin/tar]
+Where is your unzip program? [/usr/bin/unzip]
+Where is your make program? [/usr/bin/make]
+Warning: lynx not found in PATH
+(used another console to install lynx and entered location)
+Where is your lynx program? [] /usr/bin/lynx
+Where is your wget program? [/usr/bin/wget]
+Warning: ncftpget not found in PATH
+(used another console to install ncftp and entered location)
+Where is your ncftpget program? [] /usr/bin/ncftpget
+Where is your ftp program? [/usr/bin/ftp]
+Where is your gpg program? [/usr/bin/gpg]
+What is your favorite pager program? [/usr/bin/less]
+What is your favorite shell? [/bin/bash]
+Parameters for the 'perl Makefile.PL' command?
+  Your choice:  [INSTALLDIRS=site]
+Parameters for the 'make' command?
+  Your choice:  [] -j3
+Parameters for the 'make install' command?
+  Your choice:  [-j3]
+Timeout for inactivity during Makefile.PL? [0]
+Your ftp_proxy?
+Your http_proxy?
+Your no_proxy?
+Select your continent (or several nearby continents) [] 6
+Select your country (or several nearby countries) [] 4
+commit: wrote /etc/perl/CPAN/Config.pm
+edited file with:
+  'make_arg' => q[],
+  'make_install_arg' => q[],
+</code>
+Then went back to cpan using: "perl -MCPAN -e" and did "install Bundle::CPAN"
+Reponse was long and painful!
+<code>
+The following questions all require a list of host names, separated
+with spaces. If you do not have a host available for any of the
+services, then enter a single space, followed by <CR>. To accept the
+default, hit <CR>
+Enter a list of available NNTP hosts : []
+Enter a list of available SMTP hosts : []
+Enter a list of available POP3 hosts : []
+Enter a list of available SNPP hosts : []
+Enter a list of available PH Hosts   : []
+Enter a list of available TIME Hosts   : []
+Enter a list of available DAYTIME Hosts   : []
+Do you have a firewall/ftp proxy  between your machine and the internet
+If you use a SOCKS firewall answer no
+(y|n) ? [no]
+Should all FTP connections be passive (y|n) ? [no] y
+What is your local internet domain name : [] chennai.cc
+If you specified some default hosts above, it is possible for me to
+do some basic tests when you run `make test'
+This will cause `make test' to be quite a bit slower and, if your
+internet connection is via dialup, will require you to be on-line
+unless the hosts are local.
+Do you want me to run these tests (y|n) ? [yes] n
+</code>
+Next did "perl -MCPAN -e shell" again and got
+<code>
+Sorry, we have to rerun the configuration dialog for CPAN.pm due to
+some missing parameters...
+Normally CPAN.pm keeps config variables in memory and changes need to
+be saved in a separate 'o conf commit' command to make them permanent
+between sessions. If you set the 'auto_commit' option to true, changes
+to a config variable are always automatically committed to disk.
+ <auto_commit>
+Always commit changes to config variables to disk? [no] yes
+A Build.PL is run by perl in a separate process. Likewise we run
+'./Build' and './Build install' in separate processes. If you have any
+parameters you want to pass to the calls, please specify them here.
+Typical frequently used settings:
+    --install_base /home/xxx             # different installation directory
+ <mbuildpl_arg>
+Parameters for the 'perl Build.PL' command? [] --install_base /usr/lib/perl/install_base
+Parameters for the './Build' command? Setting might be:
+    --extra_linker_flags -L/usr/foo/lib  # non-standard library location
+ <mbuild_arg>
+Your choice: []
+Do you want to use a different command for './Build install'? Sudo
+users will probably prefer:
+    su root -c ./Build
+ or
+    sudo ./Build
+ or
+    /path1/to/sudo -u admin_account ./Build
+ <mbuild_install_build_command>
+or some such. Your choice: [./Build]
+Parameters for the './Build install' command? Typical frequently used
+setting:
+    --uninst 1                           # uninstall conflicting files
+ <mbuild_install_arg>
+Your choice: []
+Unknown config variable 'cpan_version_check'
+commit: wrote '/etc/perl/CPAN/Config.pm'
+cpan shell -- CPAN exploration and modules installation (v1.9402)
+Enter 'h' for help.
+</code>
+Then finally did "install Module::Install" inside CPAN and that completed

Differences

Search

QR Code